A track with two 90 degree curves to create a U shape, for one curtain which is pulled along the track by rope, either by hand or motorised.
Please complete the form below to generate a quote for your system. * = mandatory fields.
The 32 products listed below may be used in the U-Shape Wipe system.
TRA27 Cord / Handline, 8 Plait, 8 mm diameter prestretched matt black polyester cord used to operate all Triple E track systems, manual and motorised. Triple E rope has a red fleck in it and is the only rope we guarantee to work with our systems and rearfold components.
TRA12 is a floor mounted return pulley designed for use on fixed position track systems. It is intended to be screwed to the floor where the cord is tensioned by adjusting the height of the pulley with thumb screws. The overall dimensions of the Adjustable Floor Pulley are 300 m high x 90 mm wide x 75 mm at base.
TRA11 Foot stirrup is a floor level mounted pulley designed for use on a flown or movable corded track system. The stirrup at the base allows the rope to be tensioned either by placing a foot into it or hanging a weight from it. The overall dimensions of the Pulley are 300 mm high x 150 mm wide at the base with a 25 mm wide strap.
TRA13 This girder clamp provides a suspension point from the flanges of an 'I' beam. It comprises of a length of Unistrut and two square 'U' bolts each attached to cranked rectangular clamp plates. Any flange width or thickness from a rolled steel or Aluminium joist beam can be accommodated. The suspension is achieved using a TRA18 or ERL18 Studding Set. Safe Working Load data for this product is available on request.
HTDF Is a floor mounted compact hand winch to operate corded tracks where hand pulling is not suitable. It can be retro fitted to any system. The winch is roped up in a similar way to our motors.
HTDW The hand TracDrive is a compact hand winch to operate corded tracks where hand pulling is not suitable. It can be retro fitted to any system. The winch is roped up in a similar way to our motors.
Motor drive unit for all corded systems incorporating control with open/close and stop functions. Variable speed. 230 V supply. Maximum curtain weight 400 kg straight track, 300 kg curved track.
TRA16HD Wall Bracket is used to attach a track to a wall or vertical surface. The side arms are spaced 13 mm apart to allow studding or threaded rod to attach into the top channel for any of our track systems. This component has a reach of 400 mm.
TRA18 This is a 150 mm x M12 threaded rod supplied with four nuts and washers. Longer lengths of studding are available on request. This component can be used with our TRA13 Girder Clamp and TRA16 Wall Bracket Set.
TDrive Motor drive unit is a plug and play track mounted motor system for all corded tracks incorporating control with open/close and stop functions with variable speed. 230 V supply. Maximum curtain weight 300 kg straight track, 200 kg curved track. It is mainly used on UniTrack and UniBeam systems but can also be fitted to Erail.
TRADU1 and B1 Track mounted motor system 0.4 kW, 50 Hz without control. The TracDrive mounts directly beneath the track but can also be wall mounted with additional brackets TD1002F. It can drive straight or curved systems and will operate curtains weighing up to 300 kg. The motor uses TRA27 cord. It is supplied with track mounted limit switches. The motor can be wired in either Star 415 volts ac or Delta 240 volts ac. The junction box which will accept all relevant motor connections. Termination to the junction box is through hard wired cable glands.
TRA06C The four wheeled carrier is used on curved UniTrack and UniBeam tracks to attach curtains and soft goods. Standard spacing is at 300 mm (1 foot) centres and the safe working load is 25 kg. The carrier has four flanged ball raced polyurethane tyred wheels, a swivelling loop for curtain attachment and the body is moulded from MRP (metal replacement polymer) rubber strips form noise resistant buffers. Four holes in the base enable the TRA08 rearfold tag to be fitted. The 4 wheeled carrier can only be added and removed from track ends.
TRA19 is mounted on the top of UniTrack and UniBeam tracks and is a guide for the operating cord on curved tracks. Spacing is at 500 mm centres on curves and 2 m on straight sections. M12 fixings are included for UniTrack and UniBeam.
TRA21 is a curved track head pulley for UniTrack and UniBeam, it can divert the operating cords either up or down for motors, floor pulleys and winches. The Pulley projects 94 mm (3 1/2") beyond the end of the track and is 224 mm (9") in length.
TRA20 Curve master runner carries a TRA28ARM for corded curved UniTrack and UniBeam systems. The arm clamps the operating cord and guides it through the TRA19 cord guides. The carrier has a Safe Working Load of 50 kg and is used with manual and motorised systems.
TRA22 The curve return pulley diverts the operating cord above the track back towards the head pulley on curved UniTrack and UniBeam. The overall length of the component is 200 mm (8")
TRA23 Curve Suspension Bracket is required for corded curved UniTrack and UniBeam systems it works with other suspension fittings TRA13, TRA14, TRA15, TRA16 and TRA18. The top holes work as an offset plate on overlapping curved tracks. It works as a spacer for the operating cord, refer to the cording diagrams for more detail.
TRA24 This endstop is used to anchor the trailing edge of curtains on UniTrack and UniBeam tracks.
TRA14 The Hook Clamp is used for attaching UniTrack and UniBeam to tube or truss ranging in diameters from 48 mm to 51 mm. This clamp has a safe working load of 200 kg.
TDRMAS06 This mounting plate is used with TDrive and TracDrive motor units when curved track cording is required. The motor unit is rotated by 180 degrees so that the traction pulleys line up with the operating cord traveling from the TRA21 curved track head pulleys.
TRA01 250 mm long (10") UniTrack section. UniTrack sections are joined together with TRA05 joint sets.
TRA02 500 mm long (1'8") UniTrack section. UniTrack sections are joined together with TRA05 joint sets.
TRA03 1 m long (3'3") UniTrack section. UniTrack sections are joined together with TRA05 joint sets.
TRC1090 Standard curved UniTrack section, 1 m radius x 90 degrees.
TRC1590 Standard curved UniTrack section, 1.5 m radius x 90 degrees.
TRA04 2 m long (6'6") UniTrack section. UniTrack sections are joined together with TRA05 joint sets.
TRC2090 Standard curved UniTrack section, 2 m radius x 90 degrees.
TRC3090 Standard curved UniTrack section, 2 m radius x 90 degrees. This curve is made in two 45 degree sections and includes a TRA05 joint set.
TRA15 is used to suspend track sections by rope cordage or wire rope. It comprises of a forged fitting and threaded M12 bush with a solid tubular loop springing from the top outer edges of the bush. It has a test rating of 150 kg Safe Working Load.
TRA05 Joint set used to connect two UniTrack sections (straight or curved) and comprises of one M8 bolt joint set and four square steel spigots. The spigots are a close sliding fit into the track section tubes and ensure that correct alignment is maintained.
TRA16 Wall Bracket is used to attach a track to a wall or vertical surface. It is mild steel powder coated black. It screws or bolts to the wall with 10 mm fixings. The wall bracket is 265 mm long, 180 mm high and 35 mm wide.
This L-shaped bracket consists of a flat steel plate and two laser profiled sidearms. These sidearms are spaced 13mm apart to allow studding or threaded rod to attach into the top channel for any of our track systems. This component has been tested to a 100Kg safe working load at a reach of 200mm.
A complete set of components for SDrive and TDrive motors that enables wireless operation with open, close and stop functions. The sender unit requires a local single phase power supply.